International Interprotect Epoxy Primer is a high performance two pack primer/undercoat. Its perfectly formulated for polyester, vinylester, epoxy, steel, aluminium, ferro cement and timber hulls, above and below the waterline.FeaturesAn epoxy polyamide primer that can be recoated with itself for up to 6 monthsEasy to sand and quick to dryGood abrasion resistanceSpecificationsBrand: InternationalCapacity: 750mlArea: Above & Below the WaterlineSuitable for Above the Waterline: Hull, Bilge/Lockers, Exterior Cabin/Trims, Interior Cabin/TrimsSuitable for Below the Waterline: Hull, Propeller, DriveFinish/Sheen: MattSuitable Water Types: Sea Water, Fresh WaterSubstrates: Aluminium/Zinc-Galvanised Steel, Epoxy Composite/Carbon Fibre, GRP/FRP, Lead, Steel, WoodApplication Method: Brush, RollerRecommended Number of Coats: 1 – 5Practical Coverage (Brush & Roller): 9 m/LColour AvailabilityGreyWhitePreparationSTEEL: Thoroughly degrease with a suitable thinner/cleaner using the 2 cloth method prior to carrying out any mechanical cleaning. Blast damaged or corroded areas to near white metal surface as per AS1627.4 Class 2.5. If blasting is not possible, grind with 2436 grade (grit) discs to a uniform, clean, bright metal surface with a 5075 microns anchor pattern. Thin the first coat of primer 15% with suitable thinner. ALUMINIUM: Thoroughly degrease with a suitable thinner/cleaner using the 2 cloth method prior to carrying out any mechanical cleaning. Low pressure grit blast using aluminium oxide or a copper free equivalent. If blasting is not possible, power disc with 2436 grade discs to a surface profile of 5075 micron/ 23 mils. (NB Power wire brushing is not permitted as it is ineffective and wires are often steel, leading to corrosion). After being degreased the aluminium surface may be sanded, on small areas, with aluminium oxide papers to present a water break surface and, after drying, pre primed with Etch Primer. Thin the first coat of primer 15% with suitable thinner.EPOXY PRIMERS Sweep blast or abrade with 280 grade paper.EPOXY FILLERS Sand with 60120 grade (grit) paper. Do not wipe down any epoxy fillers with solvent.FERROCEMENT Allow to cure for at least 28 days above 20C/68F. Ensure structure is free from excess moisture. Remove all Maintenance, efflorescence and any other surface contaminants. Thin the first coat of primer 15% with suitable thinner.BARE GRP/COMPOSITE Ensure all waxes and uncured resins are removed. Sand with 80180 grade (grit) paper.GELCOATS Sand to remove oxidation and gloss, avoiding cutting too deep into the surface which may result in small air bubbles being exposed which will then require filling.ZINC/GALVANISED STEEL On new surfaces/those free from oxidation byproducts, thoroughly degrease with suitable thinners using the two cloth method. Oxidised surfaces will require mechanical abrasion to clean thoroughly.LEAD Thoroughly degrease with a suitable thinner/cleaner using the 2 cloth method. Rub down with an emery cloth or power wire brush. Preprime using Etch Primer where appropriate.BARE WOOD Sand with 80280 grade paper. Remove oil from oily woods eg teak, using Universal Thinner No. 3. Change rags frequently. Thin the first coat of primer 15% with suitable thinner.IMPORTANT NOTESFor further information refer to International Professional Application Manual or the International Boat Painting and Product Guide.MethodRemove blast/grinding/sanding residues with a clean air line & sweep with a clean brush, or vacuum clean for best results. On blasted and rough ground surfaces do not try and wipe with rags and thinners as the rags will catch and leave particles of cloth behind. Apply required number of coats, detailed in the specification sheets, by method chosen or stipulated, allowing required overcoating interval between applications. Thin first coat applications as detailed above.HintsMixing: Mix the two components thoroughly to an even colour. After mixing, allow to stand for 1015 minutes before using.Thinner: YTA061 International Epoxy Thinner No 7.Cleaner: YTA061 International Epoxy Thinner No 7.Ventilation and Humidity Control: Ensure adequate ventilation during use.Hazard WarningsHazard Pictogram :Signal Word:WarningHazard Statements:Flammable liquid and vapourCauses skin irritationCauses serious eye damageMay cause an allergic skin reactionHarmful to aquatic life with long lasting effectsPrecautionary Statement:General:Keep out of reach of children.Prevention:P210 – Keep away from heat / sparks / open flames / hot surfaces – No smokingP260 – Do not breathe mist / vapours / sprayP261 – Avoid breathing dust / fume / gas / mist / vapours / sprayP264 – Wash thoroughly after handlingP272 – Contaminated work clothing should not be allowed out of the workplaceP273 – Avoid release to the environmentP280 – We